Hyundai Palisade: Cruise Control System (CC) / Troubleshooting
Trouble symptom
|
Probable cause
|
Remedy
|
The set vehicle speed varies greatly upward or downward
"Surging" (repeated alternating acceleration and deceleration) occurs after
setting
|
Malfunction of the vehicle speed sensor circuit
|
Repair the vehicle speed sensor system, or replace the part
|
Malfunction of ECM
|
Check input and output signals at ECM
|
Trouble symptom
|
Probable cause
|
Remedy
|
The CC system is not canceled when the brake pedal is depressed
|
Damaged or disconnected wiring of the brake pedal switch
|
Repair the harness or replace the brake pedal switch
|
Malfunction of the ECM signals
|
Check input and output signals at ECM
|
Trouble symptom
|
Probable cause
|
Remedy
|
The CC system is not canceled when the shift lever is moved to the "N" position
(It is canceled, however, when the brake pedal is depressed)
|
Damaged or disconnected wiring of inhibitor switch input circuit
|
Repair the harness or repair or replace the inhibitor switch
|
Improper adjustment of inhibitor switch
|
Malfunction of the ECM signals
|
Check input and output signals at ECM
|
Trouble symptom
|
Probable cause
|
Remedy
|
Cannot decelerate (coast) by using the "SET/–" switch
|
Temporary damaged or disconnected wiring of "SET/–" switch input circuit
|
Repair the harness or replace the "SET/–" switch
|
Malfunction of the ECM signals
|
Check input and output signals at ECM
|
Trouble symptom
|
Probable cause
|
Remedy
|
Cannot accelerate or resume speed by using the "RES/+" switch
|
Damaged or disconnected wiring, or short circuit, or "RES/+" switch input
circuit
|
Repair the harness or replace the "RES/+" switch
|
Malfunction of the ECM signals
|
Check input and output signals at ECM
|
Trouble symptom
|
Probable cause
|
Remedy
|
CC system can be set while driving at a vehicle speed of less than 40km/h
(25mph), or there is no automatic cancellation at that speed
|
Malfunction of the vehicle-speed sensor circuit
|
Repair the vehicle speed sensor system, or replace the part
|
Malfunction of the ECM signals
|
Check input and output signals at ECM
|
Trouble symptom
|
Probable cause
|
Remedy
|
The cruise main switch indicator lamp does not illuminate (But CC system
is normal)
|
Damaged or disconnected bulb of cruise main switch indicator lamp
|
Repair the harness or replace the part.
|
Harness damaged or disconnected
|
System Block Diagram
Component Parts And Function Outline
Component part
Function
Vehicle-speed sensor, ESP/ABS Control Module
Converts vehicle speed to pulse...
Components and components location
Components
1. Remote control switch (Audio
swtich)
2. Remote control switch (Cruise
control switch)
Schematic diagrams
Circuit Diagram
Repair procedures
Removal
1...
Other information:
Troubleshooting
Limp Home Mode
•
Features a fail-safe function that prevents dangerous situations in
the event of a transaxle failure. The vehicle will be driven in limp
home mode if the transaxle malfunctions...
Interior lamp AUTO cut
The interior lamps will automatically
go off approximately 20 minutes after
the engine is turned off and the
doors are closed. If a door is opened,
the lamp will go off 40 minutes after
the engine is turned off. If the doors
are locked by the remote key or
smart key and the vehicle enters the
armed stage of the theft alarm system,
the lamps will go off five seconds
later...
Categories
Air bag warning labels, required by
the U.S. National Highway Traffic
Safety Administration (NHTSA), are
attached to alert the driver and passengers
of potential risks of the air
bag system. Be sure to read all of the
information about the air bags that
are installed on your vehicle in this
Owners Manual.
read more
Schematic diagrams
Cruise Control (CC) Switch