Hyundai Palisade (LX2): Cooling System / Coolant

Hyundai Palisade (LX2) 2020-2025 Service Manual / Engine Mechanical System / Cooling System / Coolant

Repair procedures

Replacement And Air Bleeding
Hyundai Palisade. Repair procedures   
•
Be careful not to damage the parts located under the vehicle (floor under cover, fuel filter, fuel tank and canister) when raising the vehicle using the lift.
(Refer to General Information - "Lift and Support Points")
Hyundai Palisade. Repair procedures   
•
Never remove the radiator cap when the engine is hot. Serious scalding could be caused by hot fluid under high pressure escaping from the radiator.
Hyundai Palisade. Repair procedures   
•
When pouring engine coolant, shut the relay box lid and be careful not to spill coolant on the electrical parts or the paint. Rinse off any spilt coolant immediately.
1.
Make sure the engine and radiator are cool to the touch.
2.
Remove the radiator cap (A).

Hyundai Palisade. Repair procedures
3.
Remove the engine room under cover.
(Refer to Engine and Transaxle Assembly - "Engine Room Under Cover")
4.
Loosen the drain plug (A), and drain the coolant.

Hyundai Palisade. Repair procedures
5.
Tighten the radiator drain plug securely.
6.
Remove, drain and reinstall the reservoir. Fill the tank halfway to the MAX mark with water, then up to the MAX mark with antifreeze.
7.
Fill the radiator with water through the radiator cap and tighten the cap.
Hyundai Palisade. Repair procedures   
•
To most effectively bleed air, pour water slowly while pressing on the upper / lower radiator hoses..
8.
Start the engine and allow it to warm up to normal operating temperature. Wait until the cooling fans turn on 2-3 times. Accelerate the engine to aid in purging trapped air. Shut the engine off.
9.
Wait until the engine is cool.
10.
Repeat steps 1 to 8 until the drained water runs clear.
11.
Fill with fluid mixture of coolant and water (45-60% or 45-50% in North America, Europe and China) slowly through the radiator cap.
Push the upper/lower hoses of the radiator so as to bleed air easily.
Hyundai Palisade. Repair procedures   
•
Use only the specified antifreeze/coolant.
•
For best corrosion protection, the coolant concentration must be maintained year-round at 45 - 60% minimum.
Coolant concentrations less than 45 - 60% may not provide sufficient protection against corrosion or freezing.
•
Coolant concentrations greater than 60% will impair cooling efficiency and are not recommended.
Hyundai Palisade. Repair procedures   
•
Do not mix different brands of antifreeze/coolants.
•
Do not use additional rust inhibitors or antirust products; they may not be compatible with the coolant.
12.
Start the engine and run until coolant circulates.
13.
When the cooling fan operates and coolant circulates, refill coolant through the radiator cap.
14.
Repeat step 11 until the cooling fan operates 3-5 times to sufficiently bleed air out of the cooling system.
15.
Install the radiator cap and fill the reservoir tank to the "MAX" (or "F") line with coolant.
16.
Run the vehicle under idle until the cooling fan operates 2-3 times.
17.
Stop the engine and wait for the coolant to cool down.
18.
Repeat steps 10 to 15 until the coolant level doesn't fall anymore to bleed air out of the cooling system.
Hyundai Palisade. Repair procedures   
•
Bleed air out of the cooling system and refill coolant after the coolant has cooled down completely. To do this, recheck the coolant level in the reservoir tank 2-3 days after replacing coolant.
Coolant capacity :
Approx. 11.98 L (3.16 U.S.gal., 12.66 U.S.qt., 10.54 lmp.qt.)

    Engine Overheat Troubleshooting Inspection Remedy Visual inspection Inspect for shortage of coolant in reservoir tank .

    Components and components location Components 1. Cooling fan 2. Cooling fan motor 3. Cooling fan shroud

    Other information:

    Hyundai Palisade (LX2) 2020-2025 Service Manual: Blower Unit

    Components and components location Components Location 1. Blower unit assembly Components 1. Intake seal 2. Intake upper case 3. Intake actuator 4. Intake door 5.

    Hyundai Palisade (LX2) 2020-2025 Service Manual: Special service tools

    Special Service Tools Tool Name / Number Illustration Description LKA Compensator (09890-3V100) Used for compensating front view camera unit Tolerance Compensation Plate for Surround View Monitoring (09957-CM100)

    Categories

     
    Copyright © 2025 www.hpalisadelx.com - 0.0142