Hyundai Palisade: Restraint / General information

Hyundai Palisade (LX2) 2020-2024 Service Manual / Restraint / General information

General
The supplemental restraint system (SRS) is designed to supplement the seat belt to help reduce the risk or severity of injury to the driver and passenger by activating and deploying the driver, passenger, side airbag and belt pretensioner in certain frontal or side collisions.
The SRS (Airbag) consists of ; a driver side airbag module located in the center of the steering wheel, which contains the folded cushion and an inflator unit ; a passenger side airbag module located in the passenger side crash pad contains a folded cushion assembled with an inflator unit ; side airbag modules located in the front seat contain a folded cushion and an inflator unit ; curtain airbag modules located inside the headliner contains folded cushions and inflator units. The impact sensing function of the SRSCM is carried out by an electronic accelerometer that continuously measures the vehicle’s acceleration and delivers a corresponding signal through amplifying and filtering circuitry to the microprocessor.
SRSCM (SRS Control Module)
SRSCM will detect front impact with a front impact sensor, and side impact with a side impact sensor to determine airbag module deployment.
1.
DC/DC converter : DC/DC converter in the power supply unit includes up/down transformer converter, and provide ignition voltage for 2 front airbag ignition circuits and the internal operation voltage of the SRSCM. If the internal operation voltage is below critical value setting, it will perform resetting.
2.
Back up power supply : SRSCM has a separate back up power supply, that will supply deployment energy instantly in low voltage condition or upon power failure by a frontal crash.
3.
Self diagnosis : SRSCM will constantly monitor current SRS operation status and detect system failure while vehicle power supply is on, system failure may be checked with trouble codes using GDS.
4.
Airbag warning lamp on : When an error is detected, the module will transmit a signal to the SRSCM indicator lamp located on the cluster. MIL lamp will notice the driver of SRS error. Upon ignition key on, SRS lamp will turn on for about six seconds.
5.
Trouble code registration : When an error occur in the system, SRSCM will store a DTC corresponding to the error. DTC can be cleared only by GDS. However, if an internal fault code is logged or if a crash is recorded the fault clearing should not happen.
6.
Self diagnostic connector : Data stored in SRSCM memory will be output to GDS or other external output devices through connector located below driver side crash pad.
7.
Once airbag is deployed, SRSCM should not be used again but replaced.
8.
SRSCM will determine whether passenger put on seat belt by the signal from built-in switch in seat belt buckle, and deploy front seat airbag at each set crash speed.
9.
Side airbag deployment will be determined by the SRSCM that detects satellite sensor impact signal upon a side crash, irrespective to the seat belt condition.

    Restraint

    ..

    Specifications

    Tightening Torques Item N.m kgf.m lb-ft Passenger Air Bag 8...

    Other information:

    Hyundai Palisade (LX2) 2020-2024 Service Manual: Troubleshooting


    Trouble Symptom Charts Trouble Symptom 1 Trouble Symptom 2 Trouble symptom Probable cause Remedy The set vehicle speed varies greatly upward or downward "Surging" (repeated alternating acceleration and deceleration) occurs after setting Malfunction of the vehicle speed sensor circuit Repair the vehicle speed sensor system, or replace the part Malfunction of ECM Check input and output signals at ECM Trouble Symptom 3 Trouble symptom Probable cause Remedy The CC system is not canceled when the brake pedal is depressed Damaged or disconnected wiring of the brake pedal switch Repair the harness or replace the brake pedal switch Malfunction of the ECM signals Check input and output signals at ECM Trouble Symptom 4 Trouble symptom Probable cause Remedy The CC system is not canceled when the shift lever is moved to the "N" position (It is canceled, however, when the brake pedal is depressed) Damaged or disconnected wiring of inhibitor switch input circuit Repair the harness or repair or replace the inhibitor switch Improper adjustment of inhibitor switch Malfunction of the ECM signals Check input and output signals at ECM Trouble Symptom 5 Trouble symptom Probable cause Remedy Cannot decelerate (coast) by using the "SET/–" switch Temporary damaged or disconnected wiring of "SET/–" switch input circuit Repair the harness or replace the "SET/–" switch Malfunction of the ECM signals Check input and output signals at ECM Trouble Symptom 6 Trouble symptom Probable cause Remedy Cannot accelerate or resume speed by using the "RES/+" switch Damaged or disconnected wiring, or short circuit, or "RES/+" switch input circuit Repair the harness or replace the "RES/+" switch Malfunction of the ECM signals Check input and output signals at ECM Trouble Symptom 7 Trouble symptom Probable cause Remedy CC system can be set while driving at a vehicle speed of less than 40km/h (25mph), or there is no automatic cancellation at that speed Malfunction of the vehicle-speed sensor circuit Repair the vehicle speed sensor system, or replace the part Malfunction of the ECM signals Check input and output signals at ECM Trouble Symptom 8 Trouble symptom Probable cause Remedy The cruise main switch indicator lamp does not illuminate (although CC system is normal) Damaged or disconnected bulb of cruise main switch indicator lamp Repair the harness or replace the part...

    Hyundai Palisade (LX2) 2020-2024 Service Manual: Panorama Sunroof Motor


    Repair procedures Replacement 1. Disconnect the negative (-) battery terminal. 2. Remove the roof trim assembly. (Refer to Body - "Roof Trim Assembly") 3...

    Categories

    Seat Belt Warning Light

    Seat belt warning light

    Hyundai Palisade. Seat Belt Warning Light

    Driver's seat belt warning

    As a reminder to the driver, the seat belt warning light will illuminate for approximately 6 seconds each time you place the ignition switch to the ON position regardless of belt fastening. At this time, if the seat belt is not fastened a warning chime will sound for 6 seconds.

    read more


     
    Copyright © 2024 www.hpalisadelx.com