Hyundai Palisade (LX2): Front Suspension System / Front Lower Arm

Hyundai Palisade (LX2) 2020-2026 Service Manual / Suspension System / Front Suspension System / Front Lower Arm

Repair procedures

Removal
1.
Loosen the wheel nuts slightly.
Raise the vehicle, and make sure it is securely supported.
2.
Remove the front wheel and tire (A) from the front hub.
Tightening torque :
107.9 - 127.5 N.m (11.0 - 13.0 kgf.m, 79.6 - 94.0 lb-ft)
Hyundai Palisade. Repair procedures   
•
Be careful not to damage the hub bolts when removing the front wheel and tire (A).

Hyundai Palisade. Repair procedures
3.
Remove the split pin and nut (A).
Tightening torque :
98.0 - 117.6 N.m (10.0 - 12.0 kgf.m, 72.3 - 86.7 lb-ft)

Hyundai Palisade. Repair procedures
4.
Remove the lower arm from the knuckle by using the SST (09568-4R100).
(1)
Install the support bolt (A) from lower arm bolt hole.
(2)
Install the support body (B) from front axle.
(3)
Tighten the bolt (C).

Hyundai Palisade. Repair procedures
5.
Remove the front lower arm (A) after loosening the bolts & nuts.
Tightening torque
Front :
117.7 - 137.3 N.m (12.0 - 14.0 kgf.m, 86.8 - 101.3 lb-ft)
Rear :
156.9 - 176.5 N.m (16.0 - 18.0 kgf.m, 115.7 - 130.2 lb-ft)

Hyundai Palisade. Repair procedures
Inspection
1.
Check the bushing for wear and deterioration.
2.
Check the lower arm for bending or breakage.
3.
Check the lower arm for deformation.
4.
Check the all bolts and nuts.
Replacement
1.
Loosen the wheel nuts slightly.
Raise the vehicle, and make sure it is securely supported.
2.
Remove the front wheel and tire (A) from the front hub.
Tightening torque :
107.9 - 127.5 N.m (11.0 - 13.0 kgf.m, 79.6 - 94.0 lb-ft)
Hyundai Palisade. Repair procedures   
•
Be careful not to damage the hub bolts when removing the front wheel and tire (A).

Hyundai Palisade. Repair procedures
3.
Remove the split pin and nut (A).
Tightening torque :
98.0 - 117.6 N.m (10.0 - 12.0 kgf.m, 72.3 - 86.7 lb-ft)

Hyundai Palisade. Repair procedures
4.
Remove the lower arm from the knuckle by using the SST (09568-4R100).
(1)
Install the support bolt (A) from lower arm bolt hole.
(2)
Install the support body (B) from front axle.
(3)
Tighten the bolt (C).

Hyundai Palisade. Repair procedures
5.
Remove the ball joint assembly after losening the bolt (A) and nut (B).
Tightening torque:
107.9 - 127.5N.m (11.0 - 13.0kgf.m, 79.6 - 94.0lb-ft)

Hyundai Palisade. Repair procedures

    Components and components location Components 1. Strut assembly 2. Spring lower pad 3. Dust cover 4. Coil spring 5.

    Repair procedures Removal 1. Turn the ignition switch OFF and disconnect the battery negative (-) cable. 2.

    Other information:

    Hyundai Palisade (LX2) 2020-2026 Service Manual: A/C Pressure Transducer

    Description and operation Description The A/C Pressure Transducer (APT) converts the pressure value of high pressure line into voltage value after measuring it. By converted voltage value, engine ECU controls the cooling fan by operating it high speed or low speed.

    Hyundai Palisade (LX2) 2020-2026 Service Manual: Rear Corner Safety ON/OFF Switch

    Components and components location Circuit Diagram Repair procedures Inspection 1. Disconnect the negative (-) battery terminal. 2. Remove the crash pad lower panel. (Refer to Body - "Crashpad Lower Panel") 3.

    Categories

     
    Copyright © 2026 www.hpalisadelx.com - 0.0218